Accidental Woodworker

 I got these two done right on time. My wife is going to North Carolina next week and she'll give them to the grandsons then. Wonder if kids in school even use pencils anymore? I found out that they don't teach how to write in cursive. When I went to elementary school my class year was the last one to learn cursive with ink and a pen. 

got two on before lunch

Before I got to the shop today I made a road to Whole Foods to return a cell phone holder to Amazon. I had bought one for a iPhone SE but the phone was 2" longer than the holder. I ordered an iPhone 16 holder after comparing my phone to my wife's. Height and width were the same but the thickness wasn't. My wife's phone is slightly thicker. 

That experience went well after I got help doing it. The check in counter said that it wasn't open until 0900. The lady working the self check out area helped me send it back anyway. There was an automated self help way to log it in and send it off. She saved from me having to make a return trip because I didn't see the automated option.

hmm..... (2nd big japanese toolbox)

 I had to use a hammer to get the lid open. The width was good but the ends were the headaches. The left end was a bit too snug and slid in ok but didn't like reversing itself.

done

The LN 60 1/2 worked a charm shaving both ends. It took 6 tries before the lid closed and opened easily. The lid also fit in either orientation. I had to plane a slight taper on the sliding lock batten so it cleared the side when pushed into place. Shaving the end dropped it a few frog hairs below the top edge of the side.

hmm......

I checked the outside and inside for square with each one of these. Surprised to find that all read square no matter where I checked. I did the drill again with Mr Starrett and confirmed the same as the wooden ones. However, the wooden squares were still slightly off 90 when checked with Mr Starrett. I don't understand it and it doesn't change my mind on favoring metal squares.

got 3 on

I didn't feel or see a difference in brushing this new batch of shellac on (mix with denatured alcohol vice Everclear). The build is different but that is because I mixed a 2 1/2 lb cut instead of my usual 1 1/2 lb cut. I will try to get the 4th and final coat on tonight after dinner. I want to give the shellac as much time to set up and harden as possible before they travel south.

it is mine

Decided to keep this one for myself. I already have the wooden squares in it and I'll put any other no home tools in it too. The first toolbox I made in this style I gave to my sister Donna for her husband. I told her if she doesn't want it to give to her son Sam. This box will reside in the boneyard.

accidental woodworker

new pencil box lid

A wee bit too long and too fat on the width. Still a bit apprehensive about the length but not the width. That I planed until I was happy with the wiggle room.

hmm.....

I have seen several makers of japanese boxes that used this method of battens on the lids. It doesn't lock the lid it just secures it.

finally done

These lids are continuing to bite me on the arse. It took me 3 tries before I got this fitted. Sigh. It was obvious to me that the more I make of these it ain't getting any easier.

figured it out????

You would think having to deal with only 2 fixed battens it would be a no brainer. But I think I might finally understand this. On one end of the lid the fixed batten is short about a 1/4". It is the second one that determines the outcome. I think I've been placing the fixed batten (or the sliding battens) too close to the other end.

With this lid batten method, the 2nd lid batten doesn't butt up against top box batten when it is closed. It was then it dawned on me - I could put the 2nd batten almost anywhere on the lid. Ta Da.....

a fortunate me-steak

The bottom box was first and the top one second. It was on the 2nd one that on put the 2nd batten on the wrong side of the layout line. This mistake made the placement of the 2nd batten instantly clear. Dare I say that I think I'm finally over the hump on where to place it?

nope

Pencils fit in the box but not dropping in directly between the battens. If I had made the sides longer it would have made the interior length too big. The pencils fit diagonally with space to spare.

worked  well

I used extra long cocktail toothpicks and a #49 number drill. Picked these because they were round and the others were flat. I put three toothpick nails in each top box batten. None on the bottom - I'm going with just the glue bond.

the layout

I'm glad I noticed this - the blade guard extends into the bottom and would hit the batteries. I wanted to push them up tight against the back wall but that isn't happening now.

done

I wanted to put a charger in here but there wasn't enough room . The depth was ok but I couldn't get it and the batteries in the bottom. I picked the box up after it was packed and carried it out to the truck and back down to the shop. The blade and batteries stayed home. I'll have to get by with taking two fully charged batteries to wherever this gets taken.

impatient

I went to the package store but they didn't have any large bottles of Everclear. Being impatient and needing a fresh batch of shellac, I'm using this alcohol. This is what I used to use to mix shellac before I got hung up on water content. Thinking about that I wonder what 'alcohol' the old masters used? Rum, wine, or some other distilled spirit? From reading recipes from the 17th/18th century they say to mix in spirits. I haven't read anything indicating the old masters were concerned with water in the spirits. I needed a new batch of shellac to apply to the grandson's pencil boxes.

curiosity

This is shellac is a dark brown with some red. I'm curious as to what it would look like applied to pine. Would it look like a dye? I'm about to find out. I'll have to make a road trip to the paint store and buy some empty quart cans.

another curiosity

I've had this button lac for 5 years? Bought it and the Maroon shellac above as a sample. Both of these are meant to be used with mahogany, walnut, or cherry but I'm going to try both on pine to see what 'dye' properties they have.

toast

The drawer where I stow my shellac had these squares in it. I checked everyone of them with the Starrett and all were off square. I know when I made them they were dead nuts on but over time they have drifted off into La La Land. It is because of this that I don't use them. I don't want to be bothered to stop and check that it is square before using them. So far none my metal ones have drifted in the least. However, I don't check these before use, I ass-u-me they maintain square.

accidental woodworker 

found it

There is enough for two lids from the 1/4" poplar board. I also ripped out a couple of 1 inch wide boards for battens.

what do you call this?

This thin piece of pine is necessary to strengthen this bottom spot. Reinforcing block? Bottom batten? Push comes to shove it really doesn't matter.

done

Three coats of tung oil and one coat of hard wax. A second coat of wax wasn't needed. This box will live in a drawer until I remember I have a set of these.

done

I still can't see evidence of a finish on this pencil box. Maybe the ingredients have soured or separated over the years that they sat hanging out unused. That might have something to do how the application looks.

hmm.....modification time

I was planning to store a spare blade in the top inside of the lid but nixed that. I couldn't resolve how to do it. So I switched to sawing the bottom off. I should have done this when I first made this box.

not easy

The block of wood on the back along with the handles and hinges made sawing the lid off a ROYAL PITA. I managed but it was awkward and ate up a lot of extra calories.

not through yet

Sawing the ends was the hardest with the back being the easiest.

broke off

This corner looks ugly and it was the place I started at. I broke off a wedge trying to keep the kerf open so I could saw it.

small rip panel saw

It didn't occur to me here why the rip carcass saw still hadn't sawn all the way through. It was only on the corners that I had sawn through with it.

finally

I had forgotten about these and I had sawn through a few nails too.

#6

Knocked down the proud with my #6 that has a cambered iron.

isn't pretty looking

It is flat to the eye and I did the same for the bottom. But I didn't have to use the #6 on that one.

got most of it

I wasn't able to remove all of the wandering, errant saw cuts but most of them.

wow

This is not what I was expecting. The fit is almost seamless. I thought the amount of wood I removed with the #6 would have left a few gaps and rocking.

some twist

I thought about leaving this as is but changed my mind. Wasn't sure in my mind if the hinges would work properly with the twist. Besides removing it would further smooth out the mating surfaces.

still fits

I checked to make sure that the saw would still fit. The saw plate still was laying flat on the platform.

done

I am so happy with how this came out and how it looks. The joint line looks consistent 360 - not seamless but no ugly gaps neither.

lots of room

Still kicking myself in the arse that I didn't do this from the git go.

almost done

I have a few ideas for storing saw blades and batteries. Since this the bottom I don't see any need to secure either of these down with any kind of restraints. I'll found out in the AM how well the idea is.

cooking away

Got the bottom and handles glued and cooked. I will let the box top end battens stayed clamped until tomorrow. I'm still thinking of relying on glue to keep everything together. But on the other hand I have been running using toothpicks as nails through the brain bucket.

accidental woodworker

2 coats of tung oil

I am not impressed with this finish. I think I'm stuck in a rut with the sheen and build I get from shellac. I have done several projects with this tung oil and none so far come even within 25% of the look of shellac. 

For a quick finish this is adequate and I will stay the course on it. Two coats of hard wax will start tomorrow. After I'll call this done. I already found a hole to stick it in my chisel drawer.

mortise lock chisel

This is why I bought this chisel. It is impossible to get a bench chisel on this rail vertically. I have run into this very situation on a couple of the dressers I have made in the past few years. I've been waiting (and on the email list) for about that long too waiting for Lie Nielsen to make these again. 

why not?

I have had this oil for several years. I used it once and I wasn't impressed with it. In fact I was disappointed. My results weren't anywhere near what I had seen on the internet. But I'm going to try it again and see what happens this time. I have a gloss and clear satin and I am using the gloss on this pencil box.

nada

Again, absolutely no indication that a finish of any type had been applied. I was expecting a gloss shine to show up but it looks like bare wood. The can also states that this is a one application finish. Maybe this would be different on a hardwood. For the cost of this pint can (about $25?) my expectations were dashed straight into the shit can for the last time.

pencil box prepping

I thought about making the grandson's pencil boxes out of a hardwood like cherry or walnut but nixed it. I didn't want to wait for a thin wood (3/8") to come in. I'm too impatient to wait for that. Instead I'll use up the last of the pine I resawed in half a while ago.

two pencil boxes

Everything is sawn to length and width except for the top end battens along with the locking lid battens.

yikes....

I bought these in Jan of 2022 and they have been broken and jury rigged back together for about a year. I have another set on order and I should have them tomorrow. I duct taped it back together just in case I don't get them tomorrow. I'll keep these as back up if the new ones decide to go south on me.

sizing first

I got good results using superglue on the first pencil box and I'll wash, rinse, and repeat for box 2 and 3. I soaked the end grain first and let it set up 15 minutes.

glued and cooking

I paid better attention this time clamping the boxes. I made sure that I didn't glue them up twisted. I did this glue up on a piece of 1/2" thick plywood. I left this clamped until after I got back from the post lunch stroll.

sigh

I know how I made this me-steak. I ripped this on the width with the grain when I should have ripped them to width against the grain. I had enough 1/8" plywood to get two new bottoms.

The bottoms and the two top fixed battens go a long way to strengthen and hold the box together. I would never rely solely on a super glue joint no matter what type it is.

new bottoms cooking

I thinking of not using nails on these two boxes. The glue should be sufficient to hold/keep the box together. I did think of using tapered japanese wooden nails but the size I have (the smallest ones) are too big for the thickness of the stock I used.

missing one

As I was typing this I noticed that I am short two battens. Here I have the box top end battens along with the 2 sets of the locking battens. I am missing two of the fixed lid battens. Missing are the lids too because I don't know where I hid/put the 1/4" poplar.

hmm.....

Put on a second coat of the hard oil wax and I buffed it out. It didn't do diddly for improving the shine but it did smooth it out. The 2nd coat feels a bazillion percent smoother than the first coat did. Either way the wind continues to blow I'm calling the first pencil box fini.

accidental woodworker 

 It might be a wee bit premature, but I'm calling the box done. I got the first tung oil finish on at the end of the PM session. It is going to be a few more days and a few more applications of oil and wax before it is 100% done. Close enough and I won't bore you with that.

gluing the keepers

The two long ones first and then the short end ones. I didn't miter the corners - used snug fitting butt joints.

just enough

There is a papers width on each end. It takes a bit of attention to get them in and out but I'm ok with that.

perfect

I planed a small chamfer and then rounded it over with a 120 grit sanding stick. It made the joint line look dead nuts tight 360.

yellow glue

I thought of using hide glue to secure the block but decided to go with yellow glue. If this needs any repairs or replacement I'll make a new one.

hmm.....

This tung oil finish removes/dims pencil marks. I used a micro pen on a scrap of the same plywood I used for the bottom. I wiped on the finish and rubbed it hard. Nada. I went with it but with a pencil each application of the finish, erased a bit more. Not sure what the second application will do.

almost a gotcha

The love affair with this glue dispenser almost ended. The tip had clogged shut but it was easy peasy to open it. The glue hadn't dried rock hard and it came off with a paper towel. I had been wiping it after each use and I must of forgotten doing it one time.

first one

There will be at least two coats and maybe four of the tung oil. After that I will apply a couple coats of hard wax oil.

I saw a cabinet at my niece's house the picnic day. It was tall, rectangular, and had a divided light door - 9 panes of glass. Got no idea where or who will get it but I got an itch to make one. Looking forward especially to making the door.

accidental woodworker 

 I almost got the box for the mortise lock chisels completely done. What stopped that you are obviously asking, well I'll tell you. I spent a good chunk of today driving around my boyhood town with my sister. She is leaving to go back to Indiana on tuesday and today was the only day she had free for me. She has lots of other visiting on her to do list.

We visited all the places we were grew up and the schools we attended. Our elementary school has been converted into apartments. So much of this small sleepy town I knew is gone and it has exploded with growth. Neither of us recognized most of what we saw. Oh well, stercus acidit. 

We went to a clam shack on old US Route 1 that we used to go to as kids. Well over 50 years and it is still open. We both had fish 'n chips with clam chowder and a Del's lemonade for the ride home back to Norwich. A lot of fun catching up with my oldest sister.

done

I'm not thrilled with how thin the sliding lock batten is but the sun will still rise and set. I will be putting shellac on this but that will have to wait. I need to mix up a new batch of shellac but I don't have enough Everclear for that. This will have to wait a few before that event happens.

pencils fit

I have to insert the pencils at a diagonal, but they dropped in easily. I'll have time to decide whether or not to increase the length between the battens longer than a pencil is.

early shop time

 I knew I would only have about two hours shop time in the AM so I got busy. Making the box for the chisels out of 6mm plywood. 

yikes

The lead in for the shooting plane ripped off the dado wall. I was going to make a new one but nixed it.

fillers

On the one above I only put one filler in the exit side dado. That one survived but not its sibling. With fillers in both, no problems. Both dado walls remained intact with a zero amount of blowout. 

worth a shot

I glued the broken dado wall back in place with superglue. The bottom and top dadoes will get 1/8" plywood that will be glued in them further strengthening this superglued one.

insurance

Not only did I fill in both dadoes, I used a 1/4" thick piece of pine backing up against the front edge. It worked and the superglued broken piece held up to the stress of shooting a 45.

cooking

Met my goal of getting the box glued and cooking before I had to leave to pick up my sister. This was ready to play with when I got back to the barn.

one last thing

Whacked out something to hold the two chisels. I wanted to lay the chisels flat so nothing stuck up but I didn't like the thinness of the box nor the width. I am thrilled with having the business end sticking being a cut hazard but I made it work.

ready to separate

Back at the barn and unclamped the box. Good connection on the miters (no gaps) and the corners were dead nuts square.

hmm.....

Thought I would try to separate the lid on the bandsaw. The blade is new and sharp and it is something I haven't done yet. I can't recall ever trying this on a bandsaw.

sigh.....

The cut was clean but it was also slightly tapered. It isn't much but I wasn't expecting one. 

it fits

I planed the lid and bottom until the taper pencil lines were gone. After that I refined the flatness and fit on a sheet of 60 grit sandpaper.

one more run

Noticed a wee bit of a hump in the middle of one long side. Sanded it until that hiccup disappeared. Happier with the fit this time around - and I eyeballed it and double, triple checked it twice.

got lucky

The plan was to use keepers to fit the lid on and I got lucky. There isn't a ton of a wiggle room for the chisels to fit. I can take them out and put them back in easily. It would be better is there was more clearance but this will work. It is only the keepers on the short ends that I needed to get lucky with.

finger recesses

 I don't want to take out and put these back in place by the business ends. Removed the center and chiseled two finger recesses. Plenty of room to grab the chisels.

done

I'm going with this. Sometimes later on I come up with a different way of doing things. I don't think I will with this one. I also don't anticipate using this that often for it to be a PITA.

keepers dry fitted

Made them a few frog hairs higher then the chisel ends. That should remove any blood letting hiccups.

almost at the finish line

A quick and easy box in a day. If I hadn't spent most of the day with Donna this might have been done with the exception of the shellac finish. Maybe tomorrow I'll put a check mark in the done column.

accidental woodworker

it fits

When I took the box out of the clamps it stayed together. I was half expecting it to fall apart because I used super glue to secure it.

gone

The box was twisted so badly that I didn't need the sticks to see it. Both the top and bottom were three lines twisted. It took 3 runs (top & bottom) to remove it.

the winner

I wanted to use the brass nails but they were fatter than the winners. I didn't want to risk splitting the thin stock. I predrilled for all the nails before driving them home.

bottom

Used 1/8" thick plywood for the bottom. Pencils, even with the boatload this will hold, isn't going to stress the bottom in the least.

hmm......

The one in my hand is too thin. I cut another piece of scrap pine in half and after planing it smooth it ended up about 5/16" thick.

filler

This is too fill in and add some strength to this spot. Without it was just unsupported 1/8" plywood and it would be prone to possibly breaking/splitting out.

sigh....

It was a 1/4" and in order to get it to fit I had to remove another 1/8".

screwed up

I thought it was too wide so I cut it down to 3/4". That was the me-steak. I should have stuck with the fixed batten being an inch wide. 

fits

There is about a 16th of wiggle room for dropping the lid in place.

locked in place

I think the 1/8" that is catching on the right side batten is sufficient. With the lid locked in place, I couldn't pull up and remove the lid.

fixed sliding batten

I am just using glue for securing it to the lid. I am leaving the clamps on until the AM. It is ready for finish and I have a model to build the next two of them.

came today

I had bought a set of these chisels years ago and when I took them out of the package they sliced my fingers up. None of the squared edges had been filed/chamfered. I sent them back and regretted that decision ever since. When LN sent me an email these were being made soon I asked to be notified. Bought them on sunday and they arrived today. 

These have had all the square edges relieved - nothing sharp and no blood letting this time. These aren't something that you need on a daily basis but when you do they sure are handy. I can feel an urge to make a french fitted box for them coming soon.

accidental woodworker

 

nope

It has been a long time since I played around with motors. I used to experiment with any motor I could get my hands on. Learned a ton simply by combining wiring in groups just to see what would happen. Burned out a few motors and got a boatload working but that was in the dim past. I forgot that changing the line and neutral will not effect motor rotation. The field winding wires need to be reversed.

it's the blue one

Blue 5 swapped out for Blue 6. Duh.

hmm.....

Getting the two pulleys aligned with each other was a PITA. The small one caused all the headaches due to being attached to the motor. Gently persuading that I finally got it positioned by using a pry bar. Another Duh.

first cuts

The motor was singing a different tune than the original 1/2HP one. Sounded quieter and felt stronger in the cut. I didn't notice any hiccups sawing these two - a curve and a rip cut.

one more rip cut

I was expecting this rip to be quicker and easier. It was, just not up at the level I thought it would be.

Yikes

This sucks pond scum. One thing for sure I was expecting was for this 3/4HP motor to eat resawing for lunch. It didn't happen this time.

hmm......

I didn't check the blade blocks nor the thrust bearings - upper and lower both were out. Readjusted them and tried to resaw again.

with difficulty

This resaw was a chore to do. The blade bogged and going was slow. The two parts came out ok considering that they look like snot was blown all over them.

new blade

I had bought this one specifically for resaw. That is what I mainly use my bandsaw for. The blade on it now was obviously dull or a hop, skip, and a jump from that. Time to swap in a new one.

new blade going in

Got a bit confused taking out the old blade. I thought that I would have to remove the fence rail to get the blade out. FYI - it isn't in the way. Had to reset and adjust the blocks and bearings again. The original blade was 3/8" wide and this one is 1/2".

1" thick pine

The new test subject - first a rip cut and then resawing.

resaw

The rip cut went off like I expected it too. Quick, fast, and easy. The blade sailed through it like a hot knife through butter. The resaw behaved the same. Compared it to the previous resaw it was like night and day.

smiley face on

Happy with how this resaw went off. I was able to push it though the blade with hand pressure only. With the previous set up I had to use a push stick.

like one I see

Not tapered and that is encouraging. I didn't go nutso keeping pressure up against the fence as I fed the wood through the blade.

sigh

Tapered but not as bad. The board bottom started to kick out away from the fence as I pushed it into the blade. Not as bad as previous trips through the blade and it is obviously a quirk to deal with.

helped

This is the way I have been feeding the stock through the blade. The blade is sharp and I was able to make thin cuts. I didn't try for veneer but a couple of heavy 1/8" cuts.

easy, peasy

I'm done with testing the bandsaw. I'm happy with this final result. All five of them came out with a slight, teeny bit of taper. I can live with this. I'll have to get another blade on order and check YouTube for vids on sharpening bandsaw blades.

shoulda, coulda, woulda, but didn't

I should have swapped out this motor right after I got it. I have had it for over two years but I finally took my head out of my arse and did it.

hmm.....

I see a new lot of mini japanese boxes. I think the first one I'll do is a pencil box. I tried making one of them but it came out short on the length.

cut my hair

I am amazed by how much black hair I still have. I have some graying around the temples but the rest, what little I have, is still dark brown.

done

Three coats on the errant nail box - done. Two coats of tung oil and two coats of hard paste wax on the far four - done. Got the last coat of wax rubbed out after my post lunch stroll.

new pencil box

This one will be a test box. If it goes well I will make two more of them, one each for the grandkids.

checked with a pencil

I didn't check the length of the ID of the first one I made with a pencil. Instead I made the length of the outside the same as the pencil. Forgot to take into account the battens on each end. Oops - couldn't get a pencil in the box.

inset ends

Used super glue to secure the ends. I'm putting 'handles' on this box, they are to the right of the box.

handles

Sized the ends of the handles and the ends and let that dry. After that I applied a second coat and put the box together.

glued, clamped, and cooking

Not sure what nails I'll use on this. The stock is roughly 3/8" thick and I'm leery about using cut brad nails. I have wire brads that may work better and I also have brass 18 gauge nails. I will let this set up overnight and I'll decide what to use in the AM.

accidental woodworker

 Ta da, the 3 mini japanese toolboxes are done. No drips or any other warts appeared to my eyeballs when I checked the finish on them. Glad to finally put a check mark in the done column. Which works in my favor because my sister is returning home to Indiana a week early. Saves me from having to mail them to her.

only one glamour pic

I have four more of these needing a good home. Asked my two other sisters today at a picnic and both had zero interest in them. They will collect dust in the boneyard until someone adopts them.

the errant nail box

This one is almost done. It needs one more coat of shellac before it is 100%.

cell phone holder

I gave this to my sister Donna. I think it is borderline being too large but for a dedicated purpose it is ok. I had to explain to her how to use it. The notch sailed over her head like a helium filled lead balloon.

quick run to Lowes

Got the correct cord this time. It was only 97 cents a foot and the two conductor switch cord I bought in error yesterday, was $1.12 a foot. Go figure on that one.

they fit

I had no problems getting both cords through the romex connector. No oil and no excessive cursing required to get that done.

wired

 I had plenty of room to fit the wiring without having to squish and flatten it. One last visual check of my wiring before playing with the on/off switch.

$13 male plug

This was a pleasant surprise - the plug lights up when there is juice applied. Wasn't expecting that at all. I like that because it is an indication of power available up to this point.

contact

The moment of truth came and there was much rejoicing and dancing in the streets of Mudville. No sparks, fire, or explosions when I said contact and flipped the switch. The new motor purred liked a content kitty and it sounded a lot better then the 1/2HP original motor.

one last check

Installed the cover the cover and loosely tightened the motor down on the bandsaw. The last check - motor rotation - the blade has to go downwards.

had a 50/50 chance

Big negative on the correct rotation of the motor. The blade is spinning upwards. The odd thing was it was still cutting the test piece of pine both in rip and crosscut. Don't understand that. Maybe it was cutting due to the set of the teeth?

It is simple to reverse the rotation of the motor. All it involves is switching the hot and neutral. That will have to wait until tomorrow because I had to get ready to leave for a picnic. This is the first time all the surviving kids (all four of us) have been together in over 5 years. I'll do the reversal of the wires in the AM.

accidental woodworker 

I believe that no matter the skill level you have as a woodworker, there are going to be times where you will have to take a giant step backwards. This AM I thought I would be putting a check mark in the done column for at least 3 of the japanese toolboxes. Well boys and girls I'm here to say it ain't so. I saw waterfall drips at the corners on all three of the boxes. A real big sigh and more rework after taking the giant step backwards.

waterfall drip work

Sandpaper or steel wool isn't enough alone to remove the drips. First I scrape them off with the mini card scraper. Then I follow that up with a good rubbing with 4-0 steel wool.

Lowes road trip

Bought 8 feet of tool cord, a male plug connector, and some spade connectors.

failed the bounce test

Removed the plastic cord connector and got disappointed that the romex connector didn't fit - about a 1/8" too small. The hole diameter is small and there really isn't much room to enlarge it.

possibility

This is the bottom of the cover and it could work for a romex connector. I may use this if I can't get two cords in the romex connector.

time to enlarge the hole

Before I took this off I wrote down where the wires went. Speaking from experience it can be a nightmare trying to figure out which group combination of 3 wires are.

done

Forgot that I had this step drill. This is my 2nd time using it and the first use in several years. Worked a treat with enlarging this hole - a wee bit too large but it will work.

2nd headache

The hole is too small for two cords too past through it. I drilled out the romex hole with a 5/8" drill bit.

hmm......

It is a tight fit but I'll be able to pass both of them through the hole with a little help. I think if a lube them with a bit of oil I'll be able to pull both of them through.

ugh.....

I had checked this wire before I bought it. I saw two wires and assumed a third one was buried under the paper insulation. This two conductor switch cord. The stuff I want is 3 conductor - one black, white, and green wire. I'll be making another run to Lowes tomorrow.

Checked the waterfall drip boxes in the PM and all of them looked good. All of them now look like they have a finish on them. I will do the final check tomorrow before signing off on them. 

The other four boxes got a 2nd coat of the tung oil finish. Never made it back to the shop after dinner yesterday. Tung oil does not pop at all on pine. It looks the worse on white and becomes a little discernable on darker or figured pine. Either way these last four are getting two coats of tung oil and two coats of the hard paste wax.

accidental woodworker

37C

Came close but peaked at a two digit value. Sweltering with an oppressive, wet blanket slap to the face humidity. It was uncomfortable doing the post lunch stroll today and I cut it short with a shortcut on the return trip to the barn.

Mr Darcy

He turned 18 this year and has been an indoor cat since we took him home from the animal shelter. He usually jumps up on this chair around 0700 and doesn't stir until dinner time which is around 1700. He is oblivious to the heat.

nope

I have 4 coats of the hard paste wax on these and nada. It looks like bare wood to my eye. Using the hard wax only on eastern white pine is a bust. I want some kind of indication that there is a finish applied.

shellac

I know that you can use shellac over wax because Don Williams finishing DVD told me I can. This is the second time I've applied shellac over a wax. The appearance of a finish was evident after the first coat of shellac. Three coats and I'm calling these done.

next four

These will get hard paste wax too but first they will get two coats of tung oil.

done, almost

Got three coats of shellac on them and once that is dry, I can call it 100% done. My sister said she is giving these to her grandkids for xmas this year. Plenty of time to the shellac to set and harden.

 The box at the top right is the one with the errant nail. It is getting three coats of shellac then a check mark in the done column. I'll keep this one for me to use in the shop somewhere.

one coat of tung oil

First one on post lunch stroll. The second coat might go on after dinner. Don't know what I'll use these for and I'm already thinking ahead to another run. Those I will make a little differently by putting in 'handles'.

 I didn't make the Lowes run this AM. Inside I ran a couple of errands and after them I went to the shop forgetting all about it. Good thing no one is holding a gun to my head, I'll try doing it tomorrow AM.

accidental woodworker 

going for it

No balls, no blue chips I say. Jumped into nailing off the top battens willing to risk any splitting. Besides, nailing off the top will strengthen the box's butt joinery.

sigh

First box and I got a few tiny splits on 3 of 4 of the end nails. I also got 2 splits on the center nails. But it could have been worse and I can live with the teeny splits.

this sucks

Wasn't expecting this to happen. The nail appeared to go in straight, in the middle of the end, but it came out at an angle.

lid fits in spite of it

At least the nail isn't interfering with the lid fitting. The lid still fits in both orientations too.

simple layout

I could have eyeballed it but the ruler wasn't in the way and stayed while I drilled the holes.

side trip

The fence company dropped two fence pickets off. 3 pickets were loose and I was able to nail them back in place. I got permission from my next door neighbor to walk behind her fence to get to mine and put the two new ones in. I used screws instead of nails. The fence company used what looked like aluminum spiral nails - thin and flimsy looking. They certainly pulled out easy as can be - nothing like pulling spiral nails I have dealt with before.

done

Nailed off the remaining 5 boxes. Doing it with brass nails didn't register until I was done using the cut nails.

replacement box

This is the replacement for the box with the errant nail. I tried to back it out but it wasn't happening. I don't want to chance some young fingers accidentally getting stabbed by it. Got the first coat of the hard paste wax on it. Two more to go and it can join the other 2.

I got a third coat on all of the original 3 boxes. The final coat I rubbed on a thin coat, waited 15 minutes, and buffed them with a face cloth. I didn't bother with the soft or hard buffing pads. They weren't making any difference with the look of the finish.

hmm.....

Two cords for this 1/2HP motor. One is the line cord and the other is for the on/off switch. I want to reuse the on/off switch on the 3/4HP motor. Should be doable without wasting too many calories.

this sucks pond scum

The switch and the line cords are soldered - not crimped or wire nutted together. That will make reusing this motor a wee bit involved, ie, soldering a new on/off switch. I left the wires I snipped long so I will be able to figure out how to do that.
 

old line cord

This one has had the snot beat out of it. It still works but definitely not OSHA approved. I'll have to buy a new cord at Lowes - I think they still sell line cord by the foot. This one is a few inches over 8 feet long.

hiccup

I'll have to wire the motor and switch before I secure the motor on the bandsaw. This cover will be up close and personal with the bottom frame of the bandsaw.

hmm....

This deserves a bit more than a 'hmm....'. I need to feed in two cords and that isn't going to happen. There isn't enough room for that. 

might work

There isn't a lot of extra real estate to put in a 2nd opening for a cable clamp. I'll remove this one and check if a romex clamp will fit. I should be able to get two cords in that with no problems. I don't have a good way of securing the two cords this way. And there is zero strain relief not mention it would be easy ingress for sawdust from the bandsaw.

I'll make a road trip to Lowes first thing in the AM. I rely on the bandsaw too much to have it unavailable to use. No turning back now because I can't readily swap 1/2HP motor back in service.

accidental woodworker